
QPS supports project enquiries for galvanised highway guardrail materials, including W-Beam and Thrie-Beam profiles, steel posts, spacers, fasteners and specified connecting components. Material supply must follow the road authority’s approved barrier drawings and tested restraint-system configuration.
Roadside safety performance belongs to an engineered, tested guardrail system, not to an isolated beam alone. Product selection depends on geometry, road application, containment performance, terminals, transitions, post configuration, coatings and installation requirements. QPS’s earlier page also referenced box-beam, steel-backed timber and cable barrier categories; such specialised systems should be offered only when actual compatible supply and project approval are confirmed.
QPS supports enquiries for highway guardrail products and roadside barrier components manufactured to applicable material specifications, approved profiles and project drawings.
Our range covers conventional corrugated steel guardrail profiles, related structural components and selected specialised roadside restraint systems.
Product selection depends on the approved road safety design, barrier configuration, specified containment performance, site conditions and relevant authority requirements.

Two-wave corrugated steel guardrail profiles used in approved roadside and median barrier installations.

Three-wave corrugated steel profiles used in specified roadside systems, bridge approaches and transition arrangements.

Hollow steel beam roadside barrier configurations for approved project-specific restraint systems.

Engineered roadside barrier systems combining timber appearance with specified steel reinforcement.

Tensioned steel cable restraint systems for approved median and roadside applications.

Pre-curved steel guardrail beams fabricated to approved radii and project dimensions.

Specialised sections connecting compatible barrier profiles or approved bridge and roadside restraint arrangements.

System-specific end treatment components supplied to approved barrier designs and installation details.
A typical steel highway guardrail installation consists of corrugated steel beams supported by posts and connected using specified spacer blocks, bolts, nuts and other approved accessories.
Depending on the selected restraint system, additional components may include transition sections, terminal assemblies and special connection brackets.
Each component must match the approved barrier design, structural dimensions, connection details and required installation configuration.

Corrugated steel profiles forming the longitudinal barrier.

Structural support members installed at approved spacing and embedment.

Specified components that position beams relative to posts.

System-compatible fasteners for beams, splices and posts.

Approved end-treatment products for the specified restraint system.

Special connectors for compatible barrier transitions and assemblies.
A typical steel highway guardrail installation consists of corrugated steel beams supported by posts and connected using specified spacer blocks, bolts, nuts and other approved accessories.
Depending on the selected restraint system, additional components may include transition sections, terminal assemblies and special connection brackets.
Each component must match the approved barrier design, structural dimensions, connection details and required installation configuration.

A two-corrugation profile widely used in approved roadside barrier systems.

A three-corrugation profile used in approved applications requiring a different beam geometry and restraint configuration.
Feature | W-Beam | Thrie-Beam |
|---|---|---|
Profile | Two-wave corrugation | Three-wave corrugation |
Beam depth | Shallower | Deeper |
Common use | Roadside and median barriers | Selected roadside, bridge and transition systems |
Support configuration | System-specific | System-specific |
Impact performance | Based on tested system | Based on tested system |
Connection | Compatible splice and post hardware | Compatible system-specific hardware |
QPS supports enquiries for steel highway guardrail products manufactured with suitable structural and corrugated sheet steel materials according to approved project specifications.
Guardrail beams, posts, brackets and fastening components may require galvanised finishes for corrosion protection in outdoor infrastructure environments.
Our team can review specified steel grades, sheet thicknesses, coating requirements, dimensional details and manufacturing documentation to identify appropriate sourcing options for road infrastructure projects across the UAE and GCC.
Component | Typical Specification |
|---|---|
W-Beam / Thrie-Beam | Corrugated steel conforming to applicable AASHTO M180 requirements |
Posts | Specified structural steel sections |
Spacers | Steel or other approved system-specific material |
Fasteners | Specified bolts, nuts and washers |
Coating | Hot-dip galvanising or specified approved finish |
Custom Elements | Approved drawings and material standards |
Representative Steel Guardrail Specifications
Parameter | Typical Requirement |
|---|---|
Beam Profiles | W-Beam / Thrie-Beam |
Material | Specified corrugated sheet steel |
Common Beam Thickness | Nominal 2.67–2.82 mm in selected specifications |
Beam Length | Project drawing dependent |
Hole Pattern | Approved splice and post bolt layout |
Curved Sections | Specified radius, where applicable |
Coating | Galvanised to specified standard |
Product Standard | AASHTO M180 or approved equivalent |
Guardrail Assembly Components
Parameter | Requirement |
|---|---|
Guardrail Posts | C, U, H or specified steel profiles |
Post Spacing | Approved barrier system |
Spacer Blocks | System-specific dimensions |
Bolts & Nuts | Matching approved fasteners |
Terminal Elements | Approved terminal system |
Transition Pieces | Drawing-dependent configuration |
Installation | Applicable authority and tested-system details |
Technical Standards & References
Standard | Application |
|---|---|
AASHTO M180 | Corrugated sheet steel highway guardrail beams |
ASTM A123/A123M | Hot-dip galvanised zinc coatings on fabricated steel |
ASTM A653/A653M | Zinc-coated steel sheet, where specified |
EN 1317 | Road restraint system performance and related requirements |
AASHTO MASH | Crash-test evaluation of roadside safety hardware |
Approved Authority Drawings | Barrier geometry, terminals and installation details |
Highway guardrail selection must follow the road authority’s approved restraint system, road geometry, vehicle containment requirements, site conditions and applicable technical standards.
QPS supports technical material enquiries involving guardrail beams, structural posts, spacers, fasteners and related components according to approved Bills of Quantities and project drawings.
Customers can submit barrier schedules, material specifications, approved profiles and installation requirements for commercial and sourcing review.
Selection Parameter | Example |
|---|---|
Barrier System | Approved W-Beam Guardrail |
Project | Highway Infrastructure |
Beam Length | According to approved drawing |
Steel Thickness | According to project specification |
Post Type | C-Section Steel Post |
Post Spacing | Approved barrier configuration |
Surface Finish | Hot-Dip Galvanised |
Safety Performance | Approved tested barrier system |
Quantity | 1,500 running metres |
Delivery | Abu Dhabi, UAE |

Roadside restraint components for approved highway safety systems.

Specified barrier and transition components for bridge approach and elevated roadway installations.

Guardrail components for compatible central reservation restraint systems.

Roadside barrier products for selected urban traffic and interchange projects.

Protective barrier components for approved industrial road and facility access applications.

Bulk project procurement for road development and public infrastructure works.
At QPS, we understand that highway guardrail procurement requires accurate product specifications, approved dimensions, compatible components and careful coordination of project material schedules.
Our sourcing approach supports infrastructure contractors, engineering companies and procurement teams with guardrail beam, post, spacer, fastening and related roadside barrier requirements.
Whether your enquiry involves replacement guardrail components or a larger road development project, QPS helps coordinate specification-led material enquiries across the UAE and GCC.
W-Beam, Thrie-Beam and specialised barrier enquiries.
Posts, spacers, connection hardware and terminals.
Specified protective coatings for outdoor infrastructure.
BOQ and project drawing based material enquiries.
Approved profiles, thicknesses, coating and drawing requirements.
Support for infrastructure buyers in UAE, KSA and GCC.
W-Beam has a two-wave corrugation while Thrie-Beam has a three-wave profile. The correct system must be specified by the road authority/design.
No. Crash performance depends on the complete tested assembly, including posts, height, terminals, anchorage and installation.
No. M180 relates to beam material/product requirements, while EN 1317 addresses road restraint performance and testing.
Yes. Provide the approved component list, drawings, material/coating specifications and required quantities for review.
WhatsApp us